|
|
Products mentioned in this Article
--None--
|
|
|
|
|
|
|
 |
|
PBR (Patrol Boat, River x2) (VUSBX12)
 |
PBR (Patrol Boat, River x2) (VUSBX12)
includes two PBR boats.
The Patrol Boat, River or PBR, was a small rigid-hulled patrol boat that was the mainstay of Operation Game Warden. PBRs did not usually operate with the Mobile Riverine Force; their mission was to interdict illicit waterway traffic and provide intelligence to the navy. Occasionally, this mission would overlap with the Mobile Riverine Force’s mission and the two would cooperate.
Check out the PBR (Patrol Boat, Riverine x2) in the online store here...
|
Brown Water Navy
The waterways of the Mekong Delta are busy with sampans, merchants, villages, and farming communities. They are the life blood of South Vietnam, through which over half of the entire country’s rice flows. It is remote with few roads accessing the interior’s rice fields and jungles. The Việt Cộng have launched their liberation movement from within this formidable fortress.
However, the US Army and Navy have come together to create the Mobile Riverine Force, a joint operation of infantry and assault boats. They are reinforced with helicopter gunships, devastating Skyraider aircraft and more. This new force is ready to take the fight upriver.
Learn more about Brown Water Navy here...
|
 |
 |
The PBR was usually manned by a 4-man crew. Typically, a First Class Petty Officer served as boat captain, with a gunner's mate, an engineman and a seaman on board. Each crewman was cross-trained in each other's job in case one became unable to carry out his duties. Generally, PBRs operated in pairs under the command of a patrol officer, who rode on one of the boats.
Designed by Evan Allen
Painted by Aaron Mathie
|
The PBR (Patrol Boat, River) Mk II |
 |
|
Length:
|
31’ 11” (9.8m) |
Beam: |
11’ 7” (3.5m) |
Draft: |
2’ (60cm) |
Displacement: |
16000lb (7.25tonnes) |
Speed: |
28 knots (52km/h) |
Crew: |
4 |
|
The PBR in Brown Water Navy
|
|
|
|
Armour
|
|
|
Name
|
Mobility
|
Front
|
Side
|
Top
|
Equipment and Notes
|
Weapon
|
Range
|
ROF
|
Anti-tank
|
Firepower
|
|
PBR Mk II
|
Light Tank
|
-
|
-
|
-
|
Self-defence MG.
|
Twin M2 .50cal MG |
16" / 40cm
|
5
|
4
|
5+ |
Deck turret. |
M2 .50cal MG |
16" / 40cm |
4 |
5 |
5+ |
Deck turret. |
|
 |
 |
With a shallow-draught fibreglass hull and water jet drive, the PBR could operate in the shallow, weed-choked rivers of the Mekong Delta. The dual 180hp pump-jet drives, which could be pivoted to reverse direction, made the boat extremely fast and nimble. PBRs did not have much in the way of armour protection - just some shielding for the .50-cal machine guns and upright steel armour plates in the midships. Instead, the boats were designed to rely on acceleration and maneuverability to get out of trouble. |
River Raiders
With fibreglass hulls, light patrol boats rely on their acceleration, speed, and manoeuvrability to protect them.
PBR Mk II boats have a 3+ Vehicle Save as though they were Recce teams. However, they are not automatically Destroyed if they fail the save. Instead, the opponent must make a Firepower Test to Destroy them, otherwise the boat escapes unharmed.
|
 |
 |
Contact the customer service team at [email protected] if you have any issues with any of the components. |
Step 1. Begin assembly of the Patrol Boat by gluing the radar dome into the hole in front of the boat's pilot house.
|
 |
 |
Tip: We recommend that you use good quality Super Glue to assemble resin and metal vehicles. |
Step 2. Add the Twin M2 .50cal gun to the front deck turret. |
The front deck turret goes in the hole shown below. Do not glue it into place, so it can rotate to face toward its target. |
 |
 |
 |
Step 3. Next, add the upright armored shields in the slots located in the back of the boat. Make sure the rounded corners face upwards. |
 |
 |
Step 4. Begin assembly of the rear deck turret by adding the M2 .50cal to the gunner. Make sure the pin that holds the gun into place on the boat faces downwards. |
 |
 |
Step 5. Once the bond has cured, place the gunner into the notch that holds the gun as shown below. |
 |
 |
The fully assembled PBR
|
 |
I hope you found this article helpful while assembling your PBR. Happy modelling!
~ George.
|
Last Updated On Thursday, June 4, 2015 by James at Battlefront
|
|
|